← Wiki

Which motor should you use to motorise a LEGO® Technic 1:8 car?

The large 1:8 Technic cars come without a motor, such as the Porsche 911 GT3 RS, the Bugatti Chiron, the Lamborghini Sián, the Ferrari Daytona SP3 and the McLaren P1. If you want one to drive, you build the motors in yourself. Below is what builders who did it used, what worked and what did not.

The short answer

  • Drive, LEGO only: two Technic Large Motors (88013) on the rear differential, with the Technic Hub (88012). The car drives, but slowly.
  • Drive, faster: a BuWizz 3.0 Pro with two BuWizz motors, or two Power Functions XL motors on the BuWizz. This is what most builders below used.
  • Steering: a motor that knows the position of its axle: the Technic Large Motor (88013) or the old Power Functions Servo (88004).
  • Always: take the gearbox out of the drivetrain.

The problem: weight

These cars are made to look at, not to drive. A builder who made the McLaren P1 drive weighed it at 3.7 kg with motor and battery. BuWizz built its own 1:8 supercar from 3,880 bricks and it weighs 4.3 kg. RacingBrick tested the Bugatti Chiron with two L motors and a servo. His conclusion: this set is not a good candidate for remote control, because it is so big and heavy.

Weight does not only cost power. Axles, universal joints and suspension suffer too. The P1 builder had to reinforce the rear suspension, because it stopped working under the extra weight of motor and battery.

The key lesson: take the gearbox out

In the original build the wheels also turn the gearbox and the piston engine through the differential. Put a motor on that and a lot of power is lost.

  • RacingBrick put two L motors directly on the Chiron's rear differential. To drive through the gearbox you have to remove a clutch gear that protects it, and that sits in the first building steps. His advice to readers: leave the gearbox out completely, for less friction and more room for motors. With the gearbox in, "every component would be stressed".
  • On Eurobricks, someone motorised the McLaren P1 with the gearbox and piston engine still in. With the wheels in the air everything turned smoothly, but on the ground the gears started clicking. Every reply came down to the same thing: take the gearbox out. Zerobricks, who created BuWizz, also pointed to planetary wheel hubs, which give the wheel more torque.
  • Keep the piston engine if you want to see it move, but decouple it from the drive. The BuWizz supercar moves its V10 with a separate motor.

Space for the motors is often the second problem. In the Chiron, RacingBrick replaced the original W16 engine with a more compact W16 by Didumos69 (on Rebrickable) and put the L motors underneath. The servo took the luggage space and the BuWizz the driver's seat.

What builders used per 1:8 car

WW Bricks Studio has motorised almost every large Technic car and publishes them on Rebrickable. According to their own list:

  • Ferrari Daytona SP3 (42143): BuWizz 3.0, driven by 2 Power Functions XL motors, steering with a Power Functions Servo, doors with 2 Powered Up M motors, engine cover with 1 M motor.
  • Lamborghini Sián (42115): BuWizz 3.0 with a BuWizz motor and Powered Up L and M motors. An earlier version used a BuWizz 2.0.
  • Bugatti Chiron (42083): BuWizz 3.0 with a BuWizz motor and a Powered Up L motor. Here too an earlier version used a BuWizz 2.0.
  • McLaren Formula 1 (42141): 1 BuWizz 3, 2 BuWizz motors, 1 Powered Up L motor.

Other examples:

  • Bugatti Chiron (42083), RacingBrick: 2 Power Functions L motors on the rear differential, servo at the front, BuWizz in the driver's seat. There are no instructions for it.
  • McLaren P1 (42172), Eurobricks builder Tup4n: one brushless motor with a fan, an 11.1 V battery, 3 small servos for steering, fake engine and spoiler, an RC differential, metal universal joints and axles, and a 12:20 gear ratio. He expects 32 to 35 km/h. The same system reached 40.8 km/h in a lighter 1:8 car. His warning: without cooling the motor got too hot after 5 minutes. With a fan he drives for 20 to 30 minutes.

Option 1: LEGO only (Powered Up)

The system LEGO sells today is called Powered Up, for Technic also Control+. You need the Technic Hub (88012), which has four ports. Then you choose between two motors. Philo has measured LEGO motors with the same setup for years. At 9 volts and the same load (8.81 N·cm) he found:

Speed and power are the same. Philo himself does not see the point of the bigger XL. In a full 1:8 car the smaller L fits more easily. Both motors know the position of their axle to within 1 degree, so they also work for steering.

Do not expect much speed. On Eurobricks a builder wrote that a couple of L motors in such a heavy car is "only enough for a crawl". That is an impression, not a measurement.

Rather not drive with your phone? With Pybricks, free software for the Technic Hub, you can drive the car with the LEGO remote (88010). Pybricks shows this with the Audi RS Q e-tron (42160): two drive motors and one steering motor, exactly the layout of a motorised 1:8 car. You can always go back to LEGO's software.

Option 2: BuWizz (not made by LEGO)

BuWizz is a Slovenian brand that puts battery, receiver and control in one block the size of LEGO bricks. Most of the builders above used it. According to BuWizz's own technical data:

  • BuWizz 3.0 Pro: 4 Powered Up ports (2 A continuous per port) and 2 Power Functions ports (4 A continuous per port), over 100 W in total. Replaceable 8.9 Wh battery that charges from 20 to 80 % in 35 minutes over USB-C. Bluetooth range up to 100 m. Built-in acceleration sensor. Size 9 × 4 studs, 3 bricks high.
  • Both plugs: the 3.0 Pro works with Powered Up motors and with Power Functions motors. So a LEGO motor can steer while BuWizz or PF XL motors drive.
  • BuWizz motor: has a Power Functions plug and is designed to take a wheel directly. According to BuWizz it gives 10 % more torque, 10 % more rpm and 20 % more power than the old LEGO RC buggy motor (5292). Those are the maker's figures.
  • Run time: according to BuWizz's own support, "from a few days with very light load to 30 minutes pushing the model hard".
  • Price on buwizz.com (2 November 2026, excluding VAT): BuWizz 3.0 Pro €199, 2 BuWizz motors €58, 3.0 Pro with 2 motors €239.

How far you can take it, BuWizz shows with its own 4.3 kg 1:8 supercar: 10 BuWizz motors and 5 BuWizz 3.0 Pros for the drive, plus 5 motors for the wing doors, spoiler, steering and a V10 with moving pistons. According to BuWizz it reaches 36.5 km/h. That is a design with the drive built in from the start, not a converted LEGO set.

You buy BuWizz from the maker: buwizz.com. On 2 November 2026 we did not find BuWizz at Amazon, bol or the shops on Lakea.

Option 3: SBrick (not made by LEGO)

SBrick, by the Hungarian company Vengit, is a Bluetooth receiver for Power Functions. You control it with an app and it hides inside a model, unlike LEGO's old infrared receiver. The difference from BuWizz: SBrick has no battery of its own. You connect it to a LEGO battery box with an extension cable, so the power depends on that box.

Builders often compare the two, and experiences differ by brand. If you want more power and a built-in battery, most choose BuWizz. Mind availability: on 2 November 2026 we found the SBrick in stock nowhere. Amazon UK says "currently unavailable", a Dutch shop has dropped it, and the maker's website had an expired security certificate.

More power means more wear

According to its maker, BuWizz gives up to 12 volts and more current per port than LEGO's own system. Users like that, but it comes at a price: gears, universal joints, axles and differentials wear faster. RacingBrick warns that in a full 1:8 car every component gets stressed. The fastest conversion above runs on metal universal joints, metal axles and an RC differential, precisely because the plastic parts do not hold up. So do not drive a BuWizz in its highest mode all the time, and check the universal joints and differential after driving.

Option 4: brushless (RC hobby)

The fastest converted 1:8 cars use a brushless motor from RC modelling, with a LiPo battery and metal parts. That goes outside the LEGO system: you work with separate RC electronics, modified wheel hubs and metal universal joints. The P1 example above shows what it gives (32 to 40 km/h) and what it takes: cooling, a reinforced rear suspension, and positive caster on the front wheels, which the builder says the car is "impossible to drive" without. A LiPo battery needs careful charging.

What about the old Power Functions motors?

The Power Functions XL motor (8882) holds 40 N·cm in Philo's measurements, more than the Powered Up L and XL. WW Bricks drove the Daytona SP3 with two PF XLs. LEGO no longer sells Power Functions. Shops still sell remaining stock, usually above the old retail price. The plugs do not fit a LEGO Technic Hub. They do fit a BuWizz 3.0 Pro.

How to go about it

  • Build the car with the motors in mind. The drivetrain is often in the first building steps.
  • Leave the gearbox out and drive the rear differential directly.
  • Decouple the piston engine from the wheels, or give it its own small motor.
  • Use two motors for driving and a motor that knows its position for steering.
  • Work out where the battery can go. RacingBrick used the driver's seat.
  • Turn the drivetrain by hand before you connect the motors. If it feels heavy, first read why a Technic model gets stuck.
  • Drive gently on a smooth floor. Axles, universal joints and suspension are not made for 3 to 4 kilos at speed.

Sources (read on 2 November 2026): Philo, motor measurements at 9 V · RacingBrick, Bugatti Chiron RC mod · WW Bricks Studio on Eurobricks · Eurobricks: McLaren P1 clicking · Eurobricks: McLaren P1 brushless · BuWizz tech specs · BuWizz motor · BuWizz 1:8 GTA Spano · Pybricks: 42160 with the remote