Viking Catapult versus the Nidhogg Dragon

Notable parts

• 2 parts come in a colour no other set has for that mould: Treasure Chest Bottom with Rear Slots, with Groove (Dark Bluish Gray); Treasure Chest Lid [Thick Hinge] (Dark Bluish Gray).
• 1 printed part is only in this set: Creature Body Part, Dragon Wing 19 x 11 with Marbled Trans-Orange Pattern (Dark Red) ×2.
• 9 parts appear in only a few other sets: Large Figure Skeletal, Limb, Angular 90°, 4 x 4 x 2 with 2 Ball Joints, and… (Dark Red) ×4 — also in 8940 Karzahni; Large Figure Weapon, Claw, Triple, with Axle (Dark Tan) ×4 — also in 7019 Viking Fortress against the Fafnir Dragon (all Vikings); Technic Axle and Pin Connector Perpendicular Double Split (Dark Red) ×2 — also in 4774 Scorpion Orb Launcher; Creature Body Part, Dragon Head Upper Jaw Beaked (Dark Red) — also in 7018 Viking Ship challenges the Midgard Serpent (all Vikings); Animal / Creature Body Part, Tail / Neck, Base Section with Black Pin (Dark Red) — also in 7093 Skeleton Tower, 79018 The Lonely Mountain; Animal Body Part / Plant, Tail / Neck / Branch / Trunk, Middle Section with… (Dark Red) — also in 7093 Skeleton Tower, 79018 The Lonely Mountain; Large Figure Skeletal, Limb, with 2 Ball Joints, and 1 Hole (Toa Nuva) (Dark Red) — also in 4774 Scorpion Orb Launcher, 8892 Piraka Outpost; Dish 4 x 4 Inverted [Radar] with Viking Red and Blue Shield Print (Tan) — also in 7020 Army of Vikings with Heavy Artillery Wagon, 7018 Viking Ship challenges the Midgard Serpent, 7019 Viking Fortress against the Fafnir Dragon (all Vikings); Plate Special 1 x 2 [Side Handle Closed Ends] (Dark Red) — also in 7474 Urban Avenger vs. Raptor, 7295 Dino Buggy Chaser, 8876 Scorpion Prison Cave, 7250 Clone Scout Walker.
• 1 part is otherwise only found in Vikings sets: Helmet Viking with Side Horn Holes (Speckle Black-Silver) ×2.
• 7 moulds first came out in 2005, including in this set: Animal Body Part, Barb / Claw / Tooth / Talon / Horn, Small ×18; Creature Body Part, Dragon Wing 19 x 11 with Marbled Trans-Orange Pattern ×2; Helmet Viking with Side Horn Holes ×2; Technic Axle and Pin Connector 2 x 7 with Two Ball Joint Sockets ×2; Technic Beam 1 x 2 with Ball Joint Angled ×2; and 2 more.
• 15 existing moulds first came out in their colour in 2005, including in this set: Large Figure Skeletal, Limb, Angular 90°, 4 x 4 x 2 with 2 Ball Joints, and… (Dark Red) ×4; Large Figure Weapon, Claw, Triple, with Axle (Dark Tan) ×4; Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening) (Reddish Brown) ×4; Brick Curved 2 x 2 x 2/3 Two Studs and Curved Slope End (Dark Red) ×2; Brick Sloped 30° 1 x 1 x 2/3 (Cheese Slope) (Red) ×2; and 10 more.

Calculated from Rebrickable’s public set inventories, excluding sticker sheets and spare parts.